howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
howto:7300digital [2020/03/02 18:24] – va7fi | howto:7300digital [2020/10/22 16:39] – va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== IC 7300 Settings for Digital ====== | + | ====== IC 7300 Settings for Digital |
+ | This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | ||
- | VA7FI has the following | + | So before doing anything, let's backup |
+ | * Insert an SD Card in the radio. | ||
+ | * Go to < | ||
+ | * The first time, '' | ||
+ | * Press '' | ||
- | |< | + | Later on, these settings can be applied using the '' |
- | |ACC/USB Output Select | + | |
- | |ACC/USB AF Output Level |<fc # | + | |
- | |ACC/USB AF SQL |<fc # | + | |
- | |ACC/USB AF Beep Speech... Output |<fc # | + | |
- | |ACC/USB IF Output level |50% | | + | |
- | |ACC MOD Level |50% | | + | |
- | |USB MOD Level |40% | | + | |
- | |DATA OFF MOD |<fc # | + | |
- | |DATA MOD |USB | | + | |
- | |< | + | |
- | |CI-V Baud Rate |Auto | | + | |
- | |CI-V Address | + | |
- | |CI-V Transceive | + | |
- | |CI-V USB-> | + | |
- | |CI-V Output (for ANT) | + | |
- | |CI-V USB Port |Link to [REMOTE]| | + | |
- | |< | + | |
- | |USB Serial Function | + | |
- | |< | + | |
- | |USB SEND |RTS | | + | |
- | |USB Keying (CW) | + | |
- | |USB Keying (RTTY) | + | |
- | |Inhibit Timer at USB Connection |<fc # | + | |
- | ^Mode | + | ===== Connector Settings ===== |
- | |Defaut Frequency |7.078.00 USB-D |3.739.00 LSB | | + | Now that the settings are backed up, lets tweak a few things. |
+ | |||
+ | VA7FI has the following settings on his radio. | ||
+ | | |Digital |Voice | | ||
+ | ^^^^ | ||
+ | |< | ||
+ | |ACC/USB Output Select | ||
+ | |ACC/USB AF Output Level |40% |50% | | ||
+ | |ACC/USB AF SQL |<fc # | ||
+ | |ACC/USB AF Beep Speech... Output |<fc # | ||
+ | ^^^^ | ||
+ | |ACC/USB IF Output level |<fc # | ||
+ | |ACC MOD Level | ||
+ | |USB MOD Level | ||
+ | |DATA OFF MOD |<fc # | ||
+ | ^^^^ | ||
+ | |DATA MOD |<fc # | ||
+ | |< | ||
+ | |CI-V Baud Rate |<fc # | ||
+ | |CI-V Address | ||
+ | |CI-V Transceive | ||
+ | |CI-V USB-> | ||
+ | |CI-V Output (for ANT) | ||
+ | |CI-V USB Port | ||
+ | |< | ||
+ | |USB Serial Function | ||
+ | |< | ||
+ | |USB SEND |RTS |OFF | | ||
+ | |USB Keying (CW) | ||
+ | |USB Keying (RTTY) | ||
+ | |Inhibit Timer at USB Connection |<fc # | ||
+ | |||
+ | |||
+ | ===== Filter Settings ===== | ||
+ | Next, we adjust the filter width: | ||
+ | * Press the '' | ||
+ | * Press and hold '' | ||
+ | * Press the '' | ||
+ | * Then turn the inner and outer '' | ||
+ | * Optionally, press '' | ||
+ | * When done, press the < | ||
+ | {{ : | ||
+ | |||
+ | |||
+ | |||
+ | ===== Digital and Voice settings ===== | ||
+ | |||
+ | Let's now set settings that will be specific to the voice and digital modes. | ||
+ | |||
+ | Start by adjusting all the settings in the Voice column: | ||
+ | |||
+ | ^Mode | ||
+ | |Defaut Frequency |7.078.00 USB-D |3.729.00 LSB | | ||
|< | |< | ||
- | |RF POWER | + | |RF POWER |
- | |MIC GAIN | + | |MIC GAIN |
- | |COMP | + | |COMP |
- | |MONITOR | + | |MONITOR |
|< | |< | ||
- | |P.AMP ATT |OFF |OFF | + | |P.AMP ATT |OFF|| |
- | |AGC |OFF |SLOW | | + | |AGC |OFF |MID | |
- | |NOTCH | + | |NOTCH |
- | |NB | + | |NB |
- | |NR | + | |NR |
- | |IP+ |OFF |OFF | + | |IP+ |OFF|| |
- | |VOX |OFF |OFF | + | |VOX |OFF|| |
- | |COMP | + | |COMP |
- | |1/4 |OFF |WIDE | | + | |1/4 |OFF |
- | |MONI | + | |MONI |
+ | |||
+ | * Now save the settings to the SD Card and call the file '' | ||
+ | |||
+ | Before we set the digital settings, move on to the next section and come back here after. | ||
+ | |||
+ | ===== ACG Adjustments ===== | ||
+ | For digital modes, we don't want any ACG: | ||
+ | |||
+ | * Pick a clear frequency. | ||
+ | * Press < | ||
+ | * Press and hold the '' | ||
+ | * Select the '' | ||
+ | * Optionally, set the '' | ||
+ | * Press < | ||
+ | |||
+ | Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | ||
+ | |||
+ | ===== Loading Settings ===== | ||
+ | To load the settings: < | ||
+ | |||
+ | |||
+ | ====== References ====== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[http:// | ||
howto/7300digital.txt · Last modified: 2023/10/24 21:46 by va7fi