howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
howto:7300digital [2020/03/02 19:31] – [Filter Settings] va7fi | howto:7300digital [2020/10/22 16:39] – va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== IC 7300 Settings for Digital ====== | + | ====== IC 7300 Settings for Digital |
This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | ||
Line 6: | Line 6: | ||
* Go to < | * Go to < | ||
* The first time, '' | * The first time, '' | ||
- | * Press '' | + | * Press '' |
Later on, these settings can be applied using the '' | Later on, these settings can be applied using the '' | ||
Line 12: | Line 12: | ||
===== Connector Settings ===== | ===== Connector Settings ===== | ||
- | Now that the settings are backed up, let tweak a few things. | + | Now that the settings are backed up, lets tweak a few things. |
- | VA7FI has the following settings on his radio. | + | VA7FI has the following settings on his radio. |
- | + | | |Digital |Voice | | |
- | |< | + | ^^^^ |
- | |ACC/USB Output Select | + | |< |
- | |ACC/USB AF Output Level |<fc #c0c0c0>40%</ | + | |ACC/USB Output Select |
- | |ACC/USB AF SQL |<fc # | + | |ACC/USB AF Output Level |40% |50% | |
- | |ACC/USB AF Beep Speech... Output |<fc # | + | |ACC/USB AF SQL |<fc # |
- | |ACC/USB IF Output level |50% | | + | |ACC/USB AF Beep Speech... Output |<fc # |
- | |ACC MOD Level |50% | | + | ^^^^ |
- | |USB MOD Level |40% | | + | |ACC/USB IF Output level |<fc #c0c0c0>50%</fc> || |
- | |DATA OFF MOD |<fc # | + | |ACC MOD Level |<fc #c0c0c0>50%</fc> || |
- | |DATA MOD |USB | | + | |USB MOD Level |35%--40%((Change the '' |
- | |< | + | |DATA OFF MOD |<fc # |
- | |CI-V Baud Rate |Auto | | + | ^^^^ |
- | |CI-V Address | + | |DATA MOD |<fc #c0c0c0>USB</fc> || |
- | |CI-V Transceive | + | |< |
- | |CI-V USB-> | + | |CI-V Baud Rate |<fc #c0c0c0>Auto</fc> || |
- | |CI-V Output (for ANT) | + | |CI-V Address |
- | |CI-V USB Port |Link to [REMOTE]| | + | |CI-V Transceive |
- | |< | + | |CI-V USB-> |
- | |USB Serial Function | + | |CI-V Output (for ANT) |
- | |< | + | |CI-V USB Port |<fc #c0c0c0>Link to [REMOTE]</ |
- | |USB SEND |RTS | | + | |< |
- | |USB Keying (CW) | + | |USB Serial Function |
- | |USB Keying (RTTY) | + | |< |
- | |Inhibit Timer at USB Connection |<fc # | + | |USB SEND |RTS |OFF | |
+ | |USB Keying (CW) | ||
+ | |USB Keying (RTTY) | ||
+ | |Inhibit Timer at USB Connection |<fc # | ||
Line 47: | Line 50: | ||
* Press and hold '' | * Press and hold '' | ||
* Press the '' | * Press the '' | ||
- | * Then turn the inner and outer '' | + | * Then turn the inner and outer '' |
- | * Optionally, press '' | + | * Optionally, press '' |
* When done, press the < | * When done, press the < | ||
{{ : | {{ : | ||
+ | |||
+ | |||
+ | ===== Digital and Voice settings ===== | ||
+ | |||
+ | Let's now set settings that will be specific to the voice and digital modes. | ||
+ | |||
+ | Start by adjusting all the settings in the Voice column: | ||
+ | |||
+ | ^Mode | ||
+ | |Defaut Frequency |7.078.00 USB-D |3.729.00 LSB | | ||
+ | |< | ||
+ | |RF POWER | ||
+ | |MIC GAIN | ||
+ | |COMP | ||
+ | |MONITOR | ||
+ | |< | ||
+ | |P.AMP ATT |OFF|| | ||
+ | |AGC |OFF |MID | | ||
+ | |NOTCH | ||
+ | |NB | ||
+ | |NR | ||
+ | |IP+ |OFF|| | ||
+ | |VOX |OFF|| | ||
+ | |COMP | ||
+ | |1/4 |OFF | ||
+ | |MONI | ||
+ | |||
+ | * Now save the settings to the SD Card and call the file '' | ||
+ | |||
+ | Before we set the digital settings, move on to the next section and come back here after. | ||
===== ACG Adjustments ===== | ===== ACG Adjustments ===== | ||
+ | For digital modes, we don't want any ACG: | ||
+ | |||
* Pick a clear frequency. | * Pick a clear frequency. | ||
* Press < | * Press < | ||
Line 59: | Line 94: | ||
* Select the '' | * Select the '' | ||
* Optionally, set the '' | * Optionally, set the '' | ||
- | * Press < | + | * Press <key>MENU</key> and select '' |
+ | Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | ||
+ | ===== Loading Settings ===== | ||
+ | To load the settings: < | ||
- | ===== Digital and Voice settings | + | |
- | ^Mode | + | ====== References ====== |
- | |Defaut Frequency |7.078.00 USB-D |3.739.00 LSB | | + | * [[https:// |
- | |< | + | |
- | |RF POWER | + | |
- | |MIC GAIN | + | |
- | |COMP |N/A |ON 4 | | + | |
- | |MONITOR | + | |
- | |< | + | |
- | |P.AMP ATT |OFF |OFF | + | |
- | |AGC |OFF |SLOW | | + | |
- | |NOTCH | + | |
- | |NB | + | |
- | |NR | + | |
- | |IP+ |OFF |OFF | | + | |
- | |VOX |OFF |OFF | | + | |
- | |COMP |N/A |ON | | + | |
- | |1/4 |OFF |WIDE | | + | |
- | |MONI | + | |
howto/7300digital.txt · Last modified: 2023/10/24 21:46 by va7fi