howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
howto:7300digital [2020/03/02 19:31] – [Filter Settings] va7fi | howto:7300digital [2023/10/24 21:23] – removed va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== IC 7300 Settings for Digital ====== | ||
- | This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | ||
- | |||
- | So before doing anything, let's backup the current settings in case something goes wrong: | ||
- | * Insert an SD Card in the radio. | ||
- | * Go to < | ||
- | * The first time, '' | ||
- | * Press '' | ||
- | |||
- | Later on, these settings can be applied using the '' | ||
- | |||
- | |||
- | ===== Connector Settings ===== | ||
- | Now that the settings are backed up, let tweak a few things. | ||
- | |||
- | VA7FI has the following settings on his radio. | ||
- | |||
- | |< | ||
- | |ACC/USB Output Select | ||
- | |ACC/USB AF Output Level |<fc # | ||
- | |ACC/USB AF SQL |<fc # | ||
- | |ACC/USB AF Beep Speech... Output |<fc # | ||
- | |ACC/USB IF Output level |50% | | ||
- | |ACC MOD Level |50% | | ||
- | |USB MOD Level |40% | | ||
- | |DATA OFF MOD |<fc # | ||
- | |DATA MOD |USB | | ||
- | |< | ||
- | |CI-V Baud Rate |Auto | | ||
- | |CI-V Address | ||
- | |CI-V Transceive | ||
- | |CI-V USB-> | ||
- | |CI-V Output (for ANT) | ||
- | |CI-V USB Port |Link to [REMOTE]| | ||
- | |< | ||
- | |USB Serial Function | ||
- | |< | ||
- | |USB SEND |RTS | | ||
- | |USB Keying (CW) | ||
- | |USB Keying (RTTY) | ||
- | |Inhibit Timer at USB Connection |<fc # | ||
- | |||
- | |||
- | ===== Filter Settings ===== | ||
- | Next, we adjust the filter width: | ||
- | * Press the '' | ||
- | * Press and hold '' | ||
- | * Press the '' | ||
- | * Then turn the inner and outer '' | ||
- | * Optionally, press '' | ||
- | * When done, press the < | ||
- | {{ : | ||
- | |||
- | |||
- | ===== ACG Adjustments ===== | ||
- | * Pick a clear frequency. | ||
- | * Press < | ||
- | * Press and hold the '' | ||
- | * Select the '' | ||
- | * Optionally, set the '' | ||
- | * Press < | ||
- | |||
- | |||
- | |||
- | ===== Digital and Voice settings ===== | ||
- | ^Mode | ||
- | |Defaut Frequency |7.078.00 USB-D |3.739.00 LSB | | ||
- | |< | ||
- | |RF POWER | ||
- | |MIC GAIN | ||
- | |COMP | ||
- | |MONITOR | ||
- | |< | ||
- | |P.AMP ATT |OFF |OFF | | ||
- | |AGC |OFF |SLOW | | ||
- | |NOTCH | ||
- | |NB | ||
- | |NR | ||
- | |IP+ |OFF |OFF | | ||
- | |VOX |OFF |OFF | | ||
- | |COMP | ||
- | |1/4 |OFF |WIDE | | ||
- | |MONI | ||
- | |||
howto/7300digital.txt · Last modified: 2023/10/24 21:46 by va7fi