howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
howto:7300digital [2020/03/02 20:12] – [Connector Settings] va7fi | howto:7300digital [2020/10/22 16:39] – va7fi | ||
---|---|---|---|
Line 6: | Line 6: | ||
* Go to < | * Go to < | ||
* The first time, '' | * The first time, '' | ||
- | * Press '' | + | * Press '' |
Later on, these settings can be applied using the '' | Later on, these settings can be applied using the '' | ||
Line 12: | Line 12: | ||
===== Connector Settings ===== | ===== Connector Settings ===== | ||
- | Now that the settings are backed up, let tweak a few things. | + | Now that the settings are backed up, lets tweak a few things. |
- | VA7FI has the following settings on his radio. | + | VA7FI has the following settings on his radio. |
- | + | | |Digital |Voice | | |
- | |< | + | ^^^^ |
- | |ACC/USB Output Select | + | |< |
- | |ACC/USB AF Output Level |42% | | + | |ACC/USB Output Select |
- | |ACC/USB AF SQL |OFF (Open) | | + | |ACC/USB AF Output Level |40% |50% | |
- | |ACC/USB AF Beep Speech... Output |<fc # | + | |ACC/USB AF SQL |<fc #c0c0c0>OFF (Open)</fc> || |
- | |ACC/USB IF Output level |50% | | + | |ACC/USB AF Beep Speech... Output |<fc # |
- | |ACC MOD Level |50% | | + | ^^^^ |
- | |USB MOD Level |50% | | + | |ACC/USB IF Output level |<fc #c0c0c0>50%</fc> || |
- | |DATA OFF MOD |<fc # | + | |ACC MOD Level |<fc #c0c0c0>50%</fc> || |
- | |DATA MOD |USB | | + | |USB MOD Level |35%--40%((Change the '' |
- | |< | + | |DATA OFF MOD |<fc # |
- | |CI-V Baud Rate |Auto | | + | ^^^^ |
- | |CI-V Address | + | |DATA MOD |<fc #c0c0c0>USB</fc> || |
- | |CI-V Transceive | + | |< |
- | |CI-V USB-> | + | |CI-V Baud Rate |<fc #c0c0c0>Auto</fc> || |
- | |CI-V Output (for ANT) | + | |CI-V Address |
- | |CI-V USB Port |Link to [REMOTE]| | + | |CI-V Transceive |
- | |< | + | |CI-V USB-> |
- | |USB Serial Function | + | |CI-V Output (for ANT) |
- | |< | + | |CI-V USB Port |<fc #c0c0c0>Link to [REMOTE]</ |
- | |USB SEND |RTS | | + | |< |
- | |USB Keying (CW) |OFF | | + | |USB Serial Function |
- | |USB Keying (RTTY) | + | |< |
- | |Inhibit Timer at USB Connection |<fc # | + | |USB SEND |RTS |OFF | |
+ | |USB Keying (CW) |<fc #c0c0c0>OFF</fc> || | ||
+ | |USB Keying (RTTY) | ||
+ | |Inhibit Timer at USB Connection |<fc # | ||
Line 60: | Line 63: | ||
Start by adjusting all the settings in the Voice column: | Start by adjusting all the settings in the Voice column: | ||
- | ^Mode | + | ^Mode ^Digital |
- | |Defaut Frequency | + | |Defaut Frequency |7.078.00 USB-D |3.729.00 LSB |
|< | |< | ||
- | |RF POWER | + | |RF POWER |30% |
- | |MIC GAIN | + | |MIC GAIN |
- | |COMP |ON 4 |N/A | | + | |COMP |N/A |
- | |MONITOR | + | |MONITOR |
|< | |< | ||
- | |P.AMP ATT |OFF |OFF | + | |P.AMP ATT |OFF|| |
- | |AGC |SLOW |MED | | + | |AGC |OFF |
- | |NOTCH | + | |NOTCH |
- | |NB |ON |OFF | | + | |NB |OFF |
- | |NR | + | |NR |
- | |IP+ |OFF |OFF | + | |IP+ |OFF|| |
- | |VOX |OFF |OFF | + | |VOX |OFF|| |
- | |COMP |ON |N/A | | + | |COMP |
- | |1/4 |WIDE |OFF | | + | |1/4 |OFF |WIDE | |
- | |MONI |OFF |ON | | + | |MONI |ON |OFF | |
* Now save the settings to the SD Card and call the file '' | * Now save the settings to the SD Card and call the file '' | ||
Line 91: | Line 94: | ||
* Select the '' | * Select the '' | ||
* Optionally, set the '' | * Optionally, set the '' | ||
- | * Press < | + | * Press <key>MENU</key> and select '' |
Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | ||
Line 101: | Line 104: | ||
====== References ====== | ====== References ====== | ||
* [[https:// | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[http:// | ||
howto/7300digital.txt · Last modified: 2023/10/24 21:46 by va7fi