howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
howto:7300digital [2023/10/24 21:23] – removed va7fi | howto:7300digital [2023/10/24 21:46] (current) – created va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== IC-7300 Settings and Windows Driver ====== | ||
+ | |||
+ | |||
+ | ===== Radio Settings for Digital Modes ===== | ||
+ | This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | ||
+ | |||
+ | So before doing anything, let's backup the current settings in case something goes wrong: | ||
+ | * Insert an SD Card in the radio. | ||
+ | * Go to < | ||
+ | * The first time, '' | ||
+ | * Press '' | ||
+ | |||
+ | Later on, these settings can be applied using the '' | ||
+ | |||
+ | |||
+ | ==== Connector Settings ==== | ||
+ | Now that the settings are backed up, lets tweak a few things. | ||
+ | |||
+ | VA7FI has the following settings on his radio. | ||
+ | | |Digital |Voice | | ||
+ | ^^^^ | ||
+ | |< | ||
+ | |ACC/USB Output Select | ||
+ | |ACC/USB AF Output Level |40% |50% | | ||
+ | |ACC/USB AF SQL |<fc # | ||
+ | |ACC/USB AF Beep Speech... Output |<fc # | ||
+ | ^^^^ | ||
+ | |ACC/USB IF Output level |<fc # | ||
+ | |ACC MOD Level | ||
+ | |USB MOD Level | ||
+ | |DATA OFF MOD |<fc # | ||
+ | ^^^^ | ||
+ | |DATA MOD |<fc # | ||
+ | |< | ||
+ | |CI-V Baud Rate |<fc # | ||
+ | |CI-V Address | ||
+ | |CI-V Transceive | ||
+ | |CI-V USB-> | ||
+ | |CI-V Output (for ANT) | ||
+ | |CI-V USB Port | ||
+ | |< | ||
+ | |USB Serial Function | ||
+ | |< | ||
+ | |USB SEND |RTS |OFF | | ||
+ | |USB Keying (CW) | ||
+ | |USB Keying (RTTY) | ||
+ | |Inhibit Timer at USB Connection |<fc # | ||
+ | |||
+ | |||
+ | ==== Filter Settings ==== | ||
+ | Next, we adjust the filter width: | ||
+ | * Press the '' | ||
+ | * Press and hold '' | ||
+ | * Press the '' | ||
+ | * Then turn the inner and outer '' | ||
+ | * Optionally, press '' | ||
+ | * When done, press the < | ||
+ | {{ / | ||
+ | |||
+ | |||
+ | |||
+ | ==== Digital and Voice settings ==== | ||
+ | |||
+ | Let's now set settings that will be specific to the voice and digital modes. | ||
+ | |||
+ | Start by adjusting all the settings in the Voice column: | ||
+ | |||
+ | ^Mode | ||
+ | |Defaut Frequency |7.078.00 USB-D |3.729.00 LSB | | ||
+ | |< | ||
+ | |RF POWER | ||
+ | |MIC GAIN | ||
+ | |COMP | ||
+ | |MONITOR | ||
+ | |< | ||
+ | |P.AMP ATT |OFF|| | ||
+ | |AGC |OFF |MID | | ||
+ | |NOTCH | ||
+ | |NB | ||
+ | |NR | ||
+ | |IP+ |OFF|| | ||
+ | |VOX |OFF|| | ||
+ | |COMP | ||
+ | |1/4 |OFF | ||
+ | |MONI | ||
+ | |||
+ | * Now save the settings to the SD Card and call the file '' | ||
+ | |||
+ | Before we set the digital settings, move on to the next section and come back here after. | ||
+ | |||
+ | ==== ACG Adjustments ==== | ||
+ | For digital modes, we don't want any ACG: | ||
+ | |||
+ | * Pick a clear frequency. | ||
+ | * Press < | ||
+ | * Press and hold the '' | ||
+ | * Select the '' | ||
+ | * Optionally, set the '' | ||
+ | * Press < | ||
+ | |||
+ | Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | ||
+ | |||
+ | ==== Loading Settings ==== | ||
+ | To load the settings: < | ||
+ | |||
+ | |||
+ | |||
+ | ===== IC-7300 Windows Driver ===== | ||
+ | |||
+ | Before connecting the radio the computer, the driver needs to be installed: | ||
+ | * Search for " | ||
+ | * Download the latest '' | ||
+ | * Click on the link in the '' | ||
+ | * Scroll down to the bottom of the next page | ||
+ | * Check the '' | ||
+ | * This should have downloaded a file named '' | ||
+ | * Unzip it (Extract) and run '' | ||
+ | |||
+ | Your computer may request to reboot (or not). Once done, you should see the following in your '' | ||
+ | {{ / | ||
+ | |||
+ | ====== References ====== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[http:// | ||
+ | |||
howto/7300digital.txt · Last modified: 2023/10/24 21:46 by va7fi