Differences

This shows you the differences between two versions of the page.

--- howto:7300digital [2020/03/02 18:41] – va7fi
+++ howto:7300digital [Unknown date] (current) – removed - external edit (Unknown date) 127.0.0.1
@@ Line 1: / Line 1: @@
-====== IC 7300 Settings for Digital ======
-===== Connector Settings =====
-VA7FI has the following settings on his radio.  The settings in <fc #c0c0c0>grey</fc> are there for reference only and can be different.
-|<key>MENU</key> > SET > Connectors: ||
-|ACC/USB Output Select   |AF    |
-|ACC/USB AF Output Level |<fc #c0c0c0>40%</fc>   |
-|ACC/USB AF SQL          |<fc #c0c0c0>OFF (Open)</fc> |
-|ACC/USB AF Beep Speech... Output |<fc #c0c0c0>OFF</fc> |
-|ACC/USB IF Output level |50% |
-|ACC MOD Level           |50% |
-|USB MOD Level           |40% |
-|DATA OFF MOD            |<fc #c0c0c0>MIC</fc> |
-|DATA MOD                |USB |
-|<key>MENU</key> > SET > Connectors > CI-V: ||
-|CI-V Baud Rate          |Auto |
-|CI-V Address            |note it |
-|CI-V Transceive         |ON   |
-|CI-V USB->Remote Tx Address |<fc #c0c0c0>N/A</fc> |
-|CI-V Output (for ANT)   |<fc #c0c0c0>OFF</fc> |
-|CI-V USB Port           |Link to [REMOTE]|
-|<key>MENU</key> > Set > Connectors: ||
-|USB Serial Function     |CI-V |
-|<key>MENU</key> > Set > Connectors > USB SEND Keying: ||
-|USB SEND                |RTS |
-|USB Keying (CW)         |<fc #c0c0c0>OFF</fc> |
-|USB Keying (RTTY)       |<fc #c0c0c0>OFF</fc> |
-|Inhibit Timer at USB Connection |<fc #c0c0c0>ON</fc> |
-===== Filter Settings =====
-To adjust the filter width:
-  * Press ''FIL1'' (or ''FIL2'' or ''FIL3'') button at the top of the screen (above frequency) until it says ''FIL1''.
-  * Press and hold ''FIL1'' (yes, the same button as before).
-  * Press the <key>BW</key> button and turn the ''VFO'' knob until it says "3.6k"
-  * Then turn the ''TWIN PBT'' knob (top left) to adjust the boundaries to 600 and 2600 (the picture shows 650 and 3400).  This step can be tweaked anytime on the fly to filter out unwanted signals at the edge of the band.  This is useful if say you've got strong RTTY signals activating your [[wp>Automatic_gain_control |AGC]], thus reducing the strength of the signals you're interested in.
-  * Optionally, press ''FIL1'' again to also customize ''FIL2'' and ''FIL3''.
-  * When done, press the <key>MENU</key> button and select the screen you usually like to see (''SCOPE'', ''METER'', etc)
-{{ :howto:filters.png |}}
-===== ACG Adjustments =====
-===== Digital and Voice settings =====
-^Mode             ^Digital        ^Voice |
-|Defaut Frequency |7.078.00 USB-D |3.739.00 LSB |
-|<key>MUTI</key> (select and turn the knob)  |||
-|RF POWER         |30%            |100%  |
-|MIC GAIN         |40%            |40%   |
-|COMP             |N/A            |ON 4  |
-|MONITOR          |ON 100%        |OFF 100% |
-|<key>FUNCTION</key> |||
-|P.AMP ATT        |OFF            |OFF  |
-|AGC              |OFF            |SLOW |
-|NOTCH            |OFF            |OFF  |
-|NB               |OFF            |ON   |
-|NR               |OFF            |OFF  |
-|IP+              |OFF            |OFF  |
-|VOX              |OFF            |OFF  |
-|COMP             |N/A            |ON   |
-|1/4              |OFF            |WIDE |
-|MONI             |ON             |OFF  |