howto:7300digital
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
howto:7300digital [2020/03/02 19:29] – [Filter Settings] va7fi | howto:7300digital [2023/10/24 21:46] (current) – created va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== IC 7300 Settings for Digital | + | ====== IC-7300 Settings and Windows Driver ====== |
+ | |||
+ | |||
+ | ===== Radio Settings for Digital | ||
This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | This page describes how to adjust the settings on the IC-7300 to use digital modes like FT8, JS8, or Winlink. | ||
Line 6: | Line 9: | ||
* Go to < | * Go to < | ||
* The first time, '' | * The first time, '' | ||
- | * Press '' | + | * Press '' |
Later on, these settings can be applied using the '' | Later on, these settings can be applied using the '' | ||
- | ===== Connector Settings | + | ==== Connector Settings ==== |
- | Now that the settings are backed up, let tweak a few things. | + | Now that the settings are backed up, lets tweak a few things. |
- | VA7FI has the following settings on his radio. | + | VA7FI has the following settings on his radio. |
+ | | |Digital |Voice | | ||
+ | ^^^^ | ||
+ | |< | ||
+ | |ACC/USB Output Select | ||
+ | |ACC/USB AF Output Level |40% |50% | | ||
+ | |ACC/USB AF SQL |<fc # | ||
+ | |ACC/USB AF Beep Speech... Output |<fc # | ||
+ | ^^^^ | ||
+ | |ACC/USB IF Output level |<fc # | ||
+ | |ACC MOD Level | ||
+ | |USB MOD Level | ||
+ | |DATA OFF MOD |<fc # | ||
+ | ^^^^ | ||
+ | |DATA MOD |<fc # | ||
+ | |< | ||
+ | |CI-V Baud Rate |<fc # | ||
+ | |CI-V Address | ||
+ | |CI-V Transceive | ||
+ | |CI-V USB-> | ||
+ | |CI-V Output (for ANT) | ||
+ | |CI-V USB Port | ||
+ | |< | ||
+ | |USB Serial Function | ||
+ | |< | ||
+ | |USB SEND |RTS |OFF | | ||
+ | |USB Keying (CW) | ||
+ | |USB Keying (RTTY) | ||
+ | |Inhibit Timer at USB Connection |<fc # | ||
- | |< | ||
- | |ACC/USB Output Select | ||
- | |ACC/USB AF Output Level |<fc # | ||
- | |ACC/USB AF SQL |<fc # | ||
- | |ACC/USB AF Beep Speech... Output |<fc # | ||
- | |ACC/USB IF Output level |50% | | ||
- | |ACC MOD Level |50% | | ||
- | |USB MOD Level |40% | | ||
- | |DATA OFF MOD |<fc # | ||
- | |DATA MOD |USB | | ||
- | |< | ||
- | |CI-V Baud Rate |Auto | | ||
- | |CI-V Address | ||
- | |CI-V Transceive | ||
- | |CI-V USB-> | ||
- | |CI-V Output (for ANT) | ||
- | |CI-V USB Port |Link to [REMOTE]| | ||
- | |< | ||
- | |USB Serial Function | ||
- | |< | ||
- | |USB SEND |RTS | | ||
- | |USB Keying (CW) | ||
- | |USB Keying (RTTY) | ||
- | |Inhibit Timer at USB Connection |<fc # | ||
- | + | ==== Filter Settings ==== | |
- | ===== Filter Settings | + | |
Next, we adjust the filter width: | Next, we adjust the filter width: | ||
- | * Press '' | + | * Press the '' |
* Press and hold '' | * Press and hold '' | ||
- | * Press the <key>BW</ | + | * Press the '' |
- | * Then turn the '' | + | * Then turn the inner and outer '' |
- | * Optionally, press '' | + | * Optionally, press '' |
* When done, press the < | * When done, press the < | ||
- | {{ :howto:filters.png |}} | + | {{ /howto/ |
- | ===== ACG Adjustments ===== | + | |
+ | ==== Digital and Voice settings ==== | ||
+ | |||
+ | Let's now set settings that will be specific to the voice and digital modes. | ||
+ | |||
+ | Start by adjusting all the settings in the Voice column: | ||
+ | |||
+ | ^Mode | ||
+ | |Defaut Frequency |7.078.00 USB-D |3.729.00 LSB | | ||
+ | |< | ||
+ | |RF POWER | ||
+ | |MIC GAIN | ||
+ | |COMP | ||
+ | |MONITOR | ||
+ | |< | ||
+ | |P.AMP ATT |OFF|| | ||
+ | |AGC |OFF |MID | | ||
+ | |NOTCH | ||
+ | |NB | ||
+ | |NR | ||
+ | |IP+ |OFF|| | ||
+ | |VOX |OFF|| | ||
+ | |COMP | ||
+ | |1/4 |OFF | ||
+ | |MONI | ||
+ | |||
+ | * Now save the settings to the SD Card and call the file '' | ||
+ | |||
+ | Before we set the digital settings, move on to the next section and come back here after. | ||
+ | |||
+ | ==== ACG Adjustments ==== | ||
+ | For digital modes, we don't want any ACG: | ||
* Pick a clear frequency. | * Pick a clear frequency. | ||
* Press < | * Press < | ||
Line 59: | Line 97: | ||
* Select the '' | * Select the '' | ||
* Optionally, set the '' | * Optionally, set the '' | ||
- | * Press < | + | * Press <key>MENU</key> and select '' |
+ | Now that the ACG is set, go back to the previous section and apply the settings in the Digital column. | ||
+ | ==== Loading Settings ==== | ||
+ | To load the settings: < | ||
- | ===== Digital and Voice settings | + | |
- | ^Mode | + | |
- | |Defaut Frequency |7.078.00 USB-D |3.739.00 LSB | | + | ===== IC-7300 Windows Driver |
- | |< | + | |
- | |RF POWER | + | Before connecting the radio the computer, the driver needs to be installed: |
- | |MIC GAIN | + | * Search for "ic-7300" on the [[https:// |
- | |COMP | + | |
- | |MONITOR | + | * Click on the link in the '' |
- | |< | + | * Scroll down to the bottom of the next page |
- | |P.AMP ATT |OFF |OFF | | + | * Check the '' |
- | |AGC |OFF |SLOW | | + | |
- | |NOTCH | + | * Unzip it (Extract) and run '' |
- | |NB | + | |
- | |NR | + | Your computer may request to reboot (or not). |
- | |IP+ |OFF |OFF | | + | {{ / |
- | |VOX |OFF |OFF | | + | |
- | |COMP |N/A |ON | | + | ====== References ====== |
- | |1/4 |OFF |WIDE | | + | |
- | |MONI | + | |
+ | | ||
howto/7300digital.1583206164.txt.gz · Last modified: 2020/03/02 19:29 by va7fi