User Tools

Site Tools


temp

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
temp [2021/11/07 13:28] – created va7fitemp [2026/11/15 19:04] (current) – [Other Considerations] va7fi
Line 1: Line 1:
 +====== Dipole Length ======
 +
 +===== A Bit of Theory =====
 +
 +In general, the wavelength (\$\lambda\$), frequency (\$f\$), and speed (\$v\$) of a travelling wave are related by the three equivalent relations:
 +\$$ v = \lambda f \qquad \text{or} \qquad f = \frac{v}{\lambda} \qquad \text{or} \qquad  \lambda = \frac{v}{f} \$$
 +
 +In ham radio, we often use the last equation to calculate the length of the legs of a dipole antenna:
 +
 +  * The speed of a radio wave travelling in free space is the speed of light:
 +\$$v = 300000000 \text{ m/s}\$$
 +
 +  * So using the last equation, if the frequency is in Hz, then the wavelength (in metres) is:
 +\$$ \lambda = \dfrac{300000000}{f} \$$
 +
 +  * But if we measure the frequency in MHz, then the equation becomes:
 +\$$  \lambda = \dfrac{300}{f} \$$
 +
 +  * Since each leg of a dipole is a quarter of the wavelength, each leg should measures \$ L = \frac{\lambda}{4}\$ :
 +\$$  L = \dfrac{75}{f} \text{ (in metres)} \qquad \text{or} \qquad  L = \dfrac{246}{f} \text{ in feet}\$$
 +
 +  * However, the speed of the electric field in a dipole is about 95% of the speed of light in freespace, so you'll often see these formulas instead:
 +\$$  L = \dfrac{71}{f} \text{ (in metres)} \qquad \text{or} \qquad  L = \dfrac{234}{f} \text{ in feet}\$$
 +
 +===== Some Experimentation =====
 +
 +The problem is that the velocity factor of 95% depends on many things like the size of the cable, the geometry of the antenna, what's around it, etc.  So what we can do instead is use the first formula \$ \quad v = \lambda f \quad \$ to measure what the actual speed is for our setup.  Here's how I figured out how to cut my inverted V antenna be resonant at 5.3305 MHz.
 +
 +  * The first step is to build an antenna that's a bit too long (so I can trim it).  For that, I used the original equation to get the length of each legs, and added a bit to tie the end points:
 +\$$ L = \dfrac{75}{f} = \dfrac{75}{5.3305} \approx 14.06 \text{ m} \$$
 +
 +  * Next, I set up the antenna at its final install location.
 +
 +  * I use my SWR metre to find the frequency of lowest SWR.  Mine was \$4.98\$ MHz.
 +
 +  * Now I use that with the length to calculate the speed using the first formula:
 +\$$ v = \lambda f = 14.06 \times 4.98 = 70.0 \$$
 +
 +  * I can now re-calculate the length I need based on this empirical speed:
 +\$$ \quad L = \dfrac{70.0}{5.3305} \approx 13.12 \text{ m} \quad \$$
 +
 +  * Finally, I simply trim each leg by:
 +\$$ 14.06 \text{ m} - 13.12 \text{ m} = 0.94 \text{m} \$$
 +
 +===== Other Considerations =====
 +A point that's not obvious is that while folding the end of the antenna on itself will shorten it, thus raising its resonant frequency, folding a metre is not the same as cutting a metre.
 +
 +The 60m band has four 3 kHz channels and one 15 kHz band between 5.3305 MHz and 5.4065 MHz.  Our club uses the lowest channel of 5.3305 MHz.  I chose to cut my antenna there instead of the middle of the band because it'll be very easy to fold the ends a bit if I ever need to use it higher up in the band.
 +