temp
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| temp [2026/10/01 11:34] – va7fi | temp [2026/11/15 19:04] (current) – [Other Considerations] va7fi | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Dipole Length ====== | ||
| + | |||
| + | ===== A Bit of Theory ===== | ||
| + | |||
| + | In general, the wavelength (\$\lambda\$), | ||
| + | \$$ v = \lambda f \qquad \text{or} \qquad f = \frac{v}{\lambda} \qquad \text{or} \qquad | ||
| + | |||
| + | In ham radio, we often use the last equation to calculate the length of the legs of a dipole antenna: | ||
| + | |||
| + | * The speed of a radio wave travelling in free space is the speed of light: | ||
| + | \$$v = 300000000 \text{ m/s}\$$ | ||
| + | |||
| + | * So using the last equation, if the frequency is in Hz, then the wavelength (in metres) is: | ||
| + | \$$ \lambda = \dfrac{300000000}{f} \$$ | ||
| + | |||
| + | * But if we measure the frequency in MHz, then the equation becomes: | ||
| + | \$$ \lambda = \dfrac{300}{f} \$$ | ||
| + | |||
| + | * Since each leg of a dipole is a quarter of the wavelength, each leg should measures \$ L = \frac{\lambda}{4}\$ : | ||
| + | \$$ L = \dfrac{75}{f} \text{ (in metres)} \qquad \text{or} \qquad | ||
| + | |||
| + | * However, the speed of the electric field in a dipole is about 95% of the speed of light in freespace, so you'll often see these formulas instead: | ||
| + | \$$ L = \dfrac{71}{f} \text{ (in metres)} \qquad \text{or} \qquad | ||
| + | |||
| + | ===== Some Experimentation ===== | ||
| + | |||
| + | The problem is that the velocity factor of 95% depends on many things like the size of the cable, the geometry of the antenna, what's around it, etc. So what we can do instead is use the first formula \$ \quad v = \lambda f \quad \$ to measure what the actual speed is for our setup. | ||
| + | |||
| + | * The first step is to build an antenna that's a bit too long (so I can trim it). For that, I used the original equation to get the length of each legs, and added a bit to tie the end points: | ||
| + | \$$ L = \dfrac{75}{f} = \dfrac{75}{5.3305} \approx 14.06 \text{ m} \$$ | ||
| + | |||
| + | * Next, I set up the antenna at its final install location. | ||
| + | |||
| + | * I use my SWR metre to find the frequency of lowest SWR. Mine was \$4.98\$ MHz. | ||
| + | |||
| + | * Now I use that with the length to calculate the speed using the first formula: | ||
| + | \$$ v = \lambda f = 14.06 \times 4.98 = 70.0 \$$ | ||
| + | |||
| + | * I can now re-calculate the length I need based on this empirical speed: | ||
| + | \$$ \quad L = \dfrac{70.0}{5.3305} \approx 13.12 \text{ m} \quad \$$ | ||
| + | |||
| + | * Finally, I simply trim each leg by: | ||
| + | \$$ 14.06 \text{ m} - 13.12 \text{ m} = 0.94 \text{m} \$$ | ||
| + | |||
| + | ===== Other Considerations ===== | ||
| + | A point that's not obvious is that while folding the end of the antenna on itself will shorten it, thus raising its resonant frequency, folding a metre is not the same as cutting a metre. | ||
| + | |||
| + | The 60m band has four 3 kHz channels and one 15 kHz band between 5.3305 MHz and 5.4065 MHz. Our club uses the lowest channel of 5.3305 MHz. I chose to cut my antenna there instead of the middle of the band because it'll be very easy to fold the ends a bit if I ever need to use it higher up in the band. | ||
| + | |||
