howto:winlink
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
howto:winlink [2021/05/16 22:56] – va7fi | howto:winlink [2023/11/05 05:08] (current) – va7fi | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | |||
====== Winlink ====== | ====== Winlink ====== | ||
This section outlines how to send and receive messages with [[https:// | This section outlines how to send and receive messages with [[https:// | ||
Line 75: | Line 74: | ||
* The first step is to create a script: {{ : | * The first step is to create a script: {{ : | ||
- | * In this example, I named it '' | + | * In this example, I named it '' |
- | * Once saved, select it and press **'' | + | * Once saved, select it and press **'' |
If you monitor the traffic as you connect to the digipeater, you'll notice a few things: | If you monitor the traffic as you connect to the digipeater, you'll notice a few things: | ||
Line 82: | Line 81: | ||
* Your callsign (in this case '' | * Your callsign (in this case '' | ||
* The exchange takes more than twice the time of a direct connection because unlike a voice repeater that repeats in real time, a digipeater waits for you to stop transmitting before it repeats it. | * The exchange takes more than twice the time of a direct connection because unlike a voice repeater that repeats in real time, a digipeater waits for you to stop transmitting before it repeats it. | ||
+ | |||
+ | |||
+ | <WRAP center round tip 85%> | ||
+ | As Robert pointed out (see email with '' | ||
+ | </ | ||
+ | |||
+ | Here is a short list of scripts that work as of Nov 5, 2023 (replace '' | ||
+ | <WRAP group> | ||
+ | <WRAP third column> | ||
+ | c ve7lso-8 | ||
+ | conn | ||
+ | c [callsign] | ||
+ | conn | ||
+ | </ | ||
+ | <WRAP third column> | ||
+ | c ve7wod-8 | ||
+ | conn | ||
+ | c [callsign] | ||
+ | conn | ||
+ | </ | ||
+ | <WRAP third column> | ||
+ | c ve7spr-8 | ||
+ | conn | ||
+ | c 2 [callsign] | ||
+ | conn | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | <WRAP center round important 85%> | ||
+ | Note the '' | ||
+ | VE7SPR-8} DOWNLINK CONNECT NEEDS PORT NUMBER - C P CALLSIGN | ||
+ | Found script connection response CONNECT NEEDS PORT NUMBER - C P CALLSIGN | ||
+ | </ | ||
+ | |||
==== Digipeaters ==== | ==== Digipeaters ==== | ||
Line 101: | Line 135: | ||
* Connection type: '' | * Connection type: '' | ||
* Add a script like this one:< | * Add a script like this one:< | ||
- | C ve7lso-8 | + | c ve7lso-8 |
- | Connected | + | conn |
- | + | c ve7gn-10 | |
- | C ve7gn-10 | + | conn |
- | Connected | + | |
</ | </ | ||
* Select your script and start. | * Select your script and start. | ||
In this example, my message will be sent to VE7LSO-8, which will repeat it to VE7GN-10, which will then send it to the CMS via the internet. | In this example, my message will be sent to VE7LSO-8, which will repeat it to VE7GN-10, which will then send it to the CMS via the internet. | ||
+ | |||
+ | |||
+ | |||
+ | ===== Message Templates ===== | ||
+ | |||
+ | Templates are a way to send complex pre-formatted '' | ||
+ | * Select a template from Winlink, which opens a form in your web browser. | ||
+ | * Use the web browser to fill out the form and " | ||
+ | * The attachment that's actually sent via Winlink is an '' | ||
+ | * Once the receiver opens the message, Winlink uses that '' | ||
+ | |||
+ | The result is that both the sender and the receiver see the fancy form, but only the actual information is transmitted (not the formatting). | ||
+ | |||
+ | If you use the same template often, there are two things you can do to expedite the process. | ||
+ | |||
+ | ==== Template Shortcut ==== | ||
+ | The first is to set a template shortcut: | ||
+ | * Click on '' | ||
+ | * Click on '' | ||
+ | * To use it, open a new message and click on the name you entered earlier. \\ {{ .winlink: | ||
+ | |||
+ | ==== Save Message Data ==== | ||
+ | Many templates allow you to save the message body so you can quickly reload it later. | ||
+ | * I first wrote the message I want to save **without the date** | ||
+ | * Then '' | ||
+ | |||
+ | When it's time to use it: | ||
+ | * I click on '' | ||
+ | * Click in the '' | ||
+ | * Then click '' | ||
+ | |||
+ | {{ winlinktemplate04.png }} | ||
+ | |||
+ | |||
===== EasyTerm by UZ7HO ===== | ===== EasyTerm by UZ7HO ===== |
howto/winlink.txt · Last modified: 2023/11/05 05:08 by va7fi