Sun Coast Amateur
Radio Club Society

User Tools

Site Tools

You are here: home » links » meshcore » part2
links:meshcore:part2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
links:meshcore:part2 [2026/10/29 20:08] – [Flash the Firmware] va7filinks:meshcore:part2 [2026/10/30 17:16] (current) – created - external edit (Unknown date) 127.0.0.1
Line 9: Line 9:
 </WRAP> </WRAP>
 </WRAP> </WRAP>
-This is the second part of the Meshcore Guide.  See the [[part1|first part]] to get started.+This is the second part of the Meshcore Guide.  See the [[part1|first part here]].
 ---- ----
  
 ====== Repeaters ====== ====== Repeaters ======
-{{ :links:meshcore:meshcore1.png?300|}} +  * Install a repeater like the //SenseCAP Solar Node P1-Pro// from [[https://www.seeedstudio.com/SenseCAP-Solar-Node-P1-Pro-for-Meshtastic-LoRa-p-6412.html|Seeed Studio]] or [[https://ca.robotshop.com/products/sensecap-solar-node-p1-pro-for-meshtastic-w-gps-battery |RobotShop]] 
-As mentioned in the [[#part1 |first part]], repeaters are used to extend the range of companions. With radios, the range roughly depends on three factors: +  * Use an antenna like:
-  * The antenna characteristics of **both** radios, their heights above the ground, and the line of sight between them. +
-  * The transmitting power of **both** radios. +
-  * The frequency used. +
- +
-Let's highlight here that it doesn't make sense to talk about the range of //one// radio.  For example, I might be able to reach Bob at a maximum distance of 1 km, while reaching Alice 2 km away.  That's because Alice might have a better antenna or be higher up than Bob.  If one person improves their antenna, height, or line of sight, it helps everyone communicating with them. +
- +
-That's not so with power.  If Bob increases his power, everyone will hear him better, but that won't help him hear anyone else better.  It's like if two people on opposite sides of a football field tried to talk to each other: one with a megaphone, and one without. +
- +
-As a rule of thumb, everyone should use roughly the same power, and focus on improving their antenna, line of sight, and height. +
- +
-With that in mind, to be effective, a repeater should have a good antenna, be as high as possible, and have a clear line of sight to other repeaters and companions. +
- +
- +
-====== Equipment ====== +
- +
-  * A repeater like the //SenseCAP Solar Node P1-Pro// can be purchased from [[https://www.seeedstudio.com/SenseCAP-Solar-Node-P1-Pro-for-Meshtastic-LoRa-p-6412.html|Seeed Studio]] or [[https://ca.robotshop.com/products/sensecap-solar-node-p1-pro-for-meshtastic-w-gps-battery |RobotShop]] +
-  * The antenna can be upgraded with one like:+
     * [[https://www.amazon.ca/dp/B08H8J6ZV6 |ALFA Network AOA-915-5ACM 5 dBi]]     * [[https://www.amazon.ca/dp/B08H8J6ZV6 |ALFA Network AOA-915-5ACM 5 dBi]]
     * [[https://www.amazon.ca/Waterproof-Fiberglass-SenseCAP-EasyLinkIn-SyncroB/dp/B09N2H166D/|5.8dBi Meshtastic Lora 915MHz Fiberglass Antenna]]     * [[https://www.amazon.ca/Waterproof-Fiberglass-SenseCAP-EasyLinkIn-SyncroB/dp/B09N2H166D/|5.8dBi Meshtastic Lora 915MHz Fiberglass Antenna]]
Line 40: Line 23:
     * [[https://www.amazon.ca/dp/B0FDB2BN1R/ |Superbat N Type Female to SMA Male RG316 Coaxial Cable 15cm]]     * [[https://www.amazon.ca/dp/B0FDB2BN1R/ |Superbat N Type Female to SMA Male RG316 Coaxial Cable 15cm]]
  
-====== Flashing the Firmware ====== 
  
-===== Installing a Bootloader ===== +===== Installing the Bootloader for the First Time. ===== 
-This step is optional, but it allows future updates to be performed over-the-air (OTA) via Bluetooth instead of wired via USB.  <wrap important> It is **not** required for (or compatible with) ESP32 devices like the Heltec V or T beam.</wrap>+This step is required to be able to perform future updates over-the-air (OTA) via Bluetooth.  <wrap important> It is **not** required for (or compatible with) ESP32 devices like the Heltec V or T beam.</wrap>
  
 If you already have MeshCore installed (but not the bootloader), download your current settings: If you already have MeshCore installed (but not the bootloader), download your current settings:
Line 61: Line 43:
   * Locate the "''.uf2''" file (probably in your Downloads folder).   * Locate the "''.uf2''" file (probably in your Downloads folder).
  
 +<WRAP pagebreak />
  
 Copy the bootloader over to your device: Copy the bootloader over to your device:
Line 69: Line 52:
   * The drive may close on its own right away.  This is normal.   * The drive may close on its own right away.  This is normal.
  
-<WRAP pagebreak /> 
- 
-===== Flash the Firmware ===== 
 Flash the MeshCore Firmware: Flash the MeshCore Firmware:
   * Go to https://meshcore.io/flasher   * Go to https://meshcore.io/flasher
Line 89: Line 69:
   * Select "''Disconnect''"   * Select "''Disconnect''"
  
 +<WRAP pagebreak />
  
 ===== Updating the Firmware OTA ===== ===== Updating the Firmware OTA =====
Line 130: Line 110:
   * Enter the "''Antenna Coverage''" tool   * Enter the "''Antenna Coverage''" tool
   * Where it says "''0 Coverage Layers''", click on <key>**⋮**</key> and select "''Import JSON''"   * Where it says "''0 Coverage Layers''", click on <key>**⋮**</key> and select "''Import JSON''"
-  * Import this {{:links:meshcore:coverage_layers_2026-03-27-221828.json |json file}}+  * Import [[:links:meshcore:coverage_layers_2026-03-27-221828.json |this file]]
  
  
links/meshcore/part2.1793329721.txt.gz · Last modified: by va7fi